Skip to content
Appliance Error Codes

What Does 4C Error Mean on Samsung WF45T6000A?

Error 4C on Samsung WF45T6000A: Check the water supply line. Follow the troubleshooting steps below to diagnose and fix this washer issue. 4C indicates a water supply issue in your Samsung WF45T6000A washing machine. This error means the machine isn’t receiving sufficient water flow during the fill cycle. Most users can resolve this themselves by checking water connections and restarting the washer. Start by verifying both hot and cold water taps are fully open and hoses aren’t kinked. According to Samsung’s technical documentation, 4C errors resolve without technician intervention in many cases when following proper troubleshooting. ## What Does 4C Mean? The Samsung WF45T6000A displays error code 4C when it detects inadequate water pressure or flow rate during the initial fill cycle. The washer’s internal pressure sensor monitors water intake, triggering this error if less than 1 gallon per minute enters the tub within the first 90 seconds. Unlike drainage errors (like 5C), this specifically relates to water supply problems. Samsung’s service manual confirms this error won’t cause permanent damage but will interrupt the wash cycle until resolved. ## Possible Causes 1. Water supply valves aren’t fully open - Both hot and cold valves must be rotated completely counterclockwise 2. Kinked inlet hoses - The 4-foot rubber hoses connecting to wall valves must maintain straight paths 3. Clogged inlet filters - Each hose connection contains a small mesh filter that traps debris 4. Faulty water pressure sensor - Located behind the control panel, this electronic component measures flow rate 5. Frozen pipes in winter - Interior water lines dropping below 32°F will block flow

6. Low household water pressure - The WF45T6000A requires minimum 20 psi to operate correctly ## Troubleshooting Steps StepActionExpected Result
1Verify both water taps behind washer are fully openValves turn completely counterclockwise
2Inspect inlet hoses for kinks or twistsHoses form gentle curves without sharp bends
3Disconnect hoses and clean filtersMesh filters show no sediment when held to light
4Power cycle washer (unplug for 2 minutes)Error clears after restarting
5Test water pressure at valveFlow fills 1-gallon container in under 60 seconds
6Check for error recurrenceCode 4C doesn’t reappear within 3 test cycles ## When to Call a Technician Contact Samsung-certified repair if:
  • Error persists after completing all troubleshooting steps
  • Water pressure tests below 20 psi at wall valves
  • You hear buzzing from the water inlet valve during fill cycles
  • The control panel shows burnt components or melted plastic
  • Repair costs exceed $150 (average pressure sensor replacement cost) Technicians have specialized tools to diagnose:
  • Faulty pressure sensors (requires multimeter testing)
  • Clogged internal water valves
  • Motherboard communication failures
  • Improper factory calibration ## Frequently Asked Questions ### How urgent is fixing error code 4C? Address within 48 hours. Prolonged dry operation can damage the pump and tub bearings.

Can I bypass this error to finish laundry? Never bypass safety codes. Samsung explicitly warns this may void warranties and risk leaks.

Section titled “Can I bypass this error to finish laundry? Never bypass safety codes. Samsung explicitly warns this may void warranties and risk leaks.”

Does this error affect both hot and cold water? Yes. The WF45T6000A checks total water flow regardless of temperature selection.

Section titled “Does this error affect both hot and cold water? Yes. The WF45T6000A checks total water flow regardless of temperature selection.”

What’s the average repair cost for persistent 4C errors? Service data shows many cases cost under $100 (mostly hose replacements), while some cases require for sensor or valve repairs.

Section titled “What’s the average repair cost for persistent 4C errors? Service data shows many cases cost under $100 (mostly hose replacements), while some cases require for sensor or valve repairs.”

Will resetting the washer clear error 4C temporarily? Power cycling may provide 1-2 successful cycles, but the root cause must be fixed per Samsung’s troubleshooting protocol. ### Is it safe to keep using my Samsung WF45T6000A with error 4C? If error 4C does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error 4C on a Samsung WF45T6000A? Repair costs for error 4C on the Samsung WF45T6000A washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Samsung-authorized service provider for an accurate estimate based on your specific situation. ### What does error code 4C mean on a Samsung washer? Error code 4C on Samsung washer models indicates Check the water supply line. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.

Section titled “Will resetting the washer clear error 4C temporarily? Power cycling may provide 1-2 successful cycles, but the root cause must be fixed per Samsung’s troubleshooting protocol. ### Is it safe to keep using my Samsung WF45T6000A with error 4C? If error 4C does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error 4C on a Samsung WF45T6000A? Repair costs for error 4C on the Samsung WF45T6000A washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Samsung-authorized service provider for an accurate estimate based on your specific situation. ### What does error code 4C mean on a Samsung washer? Error code 4C on Samsung washer models indicates Check the water supply line. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.”