Skip to content
Appliance Error Codes

What Does F5 Error Mean on Whirlpool WRS325SDHZ?

Error F5 on Whirlpool WRS325SDHZ: Defrost sensor failure — the freezer defrost sensor or defrost thermostat has fa. Follow the troubleshooting steps below to diagnose and fix this refrigerator issue. The F5 error code on your Whirlpool refrigerator indicates a problem with the defrost sensor or defrost thermostat in the freezer section. These components work together to control the automatic defrost cycle that prevents ice from building up on the evaporator coils. If left unresolved, excessive ice accumulation can reduce cooling efficiency significantly. Schedule professional service if a power reset does not clear F5. ## What Does F5 Mean? The automatic defrost system on Whirlpool refrigerators uses a defrost heater, a defrost sensor (thermistor), and a defrost thermostat (safety high-limit thermostat) to melt frost that accumulates on the evaporator coils during normal operation. The defrost sensor monitors evaporator temperature to determine when defrost should begin and when the coils are clear. The thermostat acts as a safety limit, cutting power to the heater if temperatures become too high. F5 appears when the control board detects that the defrost sensor is reading outside its expected range — either too high, too low, or open circuit. Without accurate sensor readings, the control board cannot manage the defrost cycle safely. On WRF535SWHZ and WRX735SDHZ models, the evaporator is located behind the rear wall of the freezer compartment. Ice accumulation on the evaporator from a failed defrost cycle gradually blocks airflow, causing both the freezer and refrigerator sections to warm up even though the compressor is running. ## Possible Causes 1. Failed defrost sensor (thermistor) with resistance outside normal operating range 2. Failed defrost thermostat (high-limit safety thermostat) that has opened permanently 3. Open circuit in the wiring harness from the defrost sensor to the main control board 4. Loose wiring connector at the defrost sensor or thermostat terminals 5. Excessive ice buildup on the evaporator from a prior defrost failure that damaged the sensor by overheating ## Troubleshooting Steps | Step | Action | Expected Result | |------|--------|-----------------| | 1 | Perform a refrigerator power reset by unplugging for 10 minutes, then restore power and run the refrigerator for 24 hours to see if F5 returns | F5 does not return — fault was a temporary sensor reading | | 2 | If F5 returns, check the freezer interior for unusual ice buildup on the back wall, which indicates the defrost cycle has been failing | Heavy frost on back wall confirms defrost system issue requiring service | | 3 | If frost buildup is present, do not attempt to manually defrost with a heat gun or sharp objects — unplug the refrigerator and allow the freezer to thaw with doors open for 24 hours | Frost melts naturally — manually inspect the sensor and thermostat wiring after thaw | | 4 | Schedule service for defrost sensor and thermostat testing and replacement | Technician identifies faulty component and replaces defrost sensor or thermostat | Do not use a hairdryer, heat gun, or ice pick to manually remove frost from the evaporator coils. These methods can damage the evaporator fins, puncture the refrigerant tubing, or cause electrical hazards. Manual defrost should be done by unplugging the refrigerator and allowing natural thawing. ## When to Call a Technician Contact Whirlpool authorized service if: - F5 returns after a 10-minute power reset and the freezer back wall has a thick layer of frost

  • Both the refrigerator and freezer sections are not reaching set temperatures even though the compressor is running
  • You can hear the defrost heater clicking or the smell of burning plastic from the freezer compartment Professional repair costs for F5 issues typically range from $80 to $220 depending on the specific component and your service region. ## Frequently Asked Questions ### What happens if I ignore the F5 code on my Whirlpool refrigerator? If F5 is ignored and the defrost sensor has failed, frost will continue to build up on the evaporator coils with each compressor cycle. Over days to weeks, this ice accumulation can completely block airflow from the evaporator fan, causing both the refrigerator and freezer sections to gradually warm up. Food spoilage can result if the ice buildup becomes severe.

How often does the Whirlpool refrigerator defrost cycle run? Most Whirlpool refrigerators run a defrost cycle approximately every 8 to 12 hours. The defrost heater runs for about 20 to 30 minutes during each cycle. If F5 is present and the defrost cycle is not running, you will notice frost accumulation accelerating after each day of use.

Section titled “How often does the Whirlpool refrigerator defrost cycle run? Most Whirlpool refrigerators run a defrost cycle approximately every 8 to 12 hours. The defrost heater runs for about 20 to 30 minutes during each cycle. If F5 is present and the defrost cycle is not running, you will notice frost accumulation accelerating after each day of use.”

Can I test the defrost sensor on my Whirlpool refrigerator myself? With a multimeter, you can measure resistance across the defrost sensor terminals after disconnecting the refrigerator. The resistance value depends on temperature, but a reading of open circuit (OL or infinite resistance) at room temperature confirms sensor failure. The defrost thermostat should show continuity (near 0 ohms) at room temperature and open at its rated high temperature.

Section titled “Can I test the defrost sensor on my Whirlpool refrigerator myself? With a multimeter, you can measure resistance across the defrost sensor terminals after disconnecting the refrigerator. The resistance value depends on temperature, but a reading of open circuit (OL or infinite resistance) at room temperature confirms sensor failure. The defrost thermostat should show continuity (near 0 ohms) at room temperature and open at its rated high temperature.”

Is F5 always a defrost sensor failure? F5 most commonly indicates a defrost sensor or defrost thermostat fault. However, a broken wire in the harness connecting these components to the control board produces the same symptom. Always inspect the wiring connectors at the defrost sensor and thermostat locations before ordering replacement parts. Reference: Whirlpool official support documentation (whirlpool.com/support) and authorized service guides ### Is it safe to keep using my Whirlpool WRS325SDHZ with error F5? If error F5 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the refrigerator with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error F5 on a Whirlpool WRS325SDHZ? Repair costs for error F5 on the Whirlpool WRS325SDHZ refrigerator depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Whirlpool-authorized service provider for an accurate estimate based on your specific situation. ### What does error code F5 mean on a Whirlpool refrigerator? Error code F5 on Whirlpool refrigerator models indicates Defrost sensor failure — the freezer defrost sensor or defrost thermostat has failed or its circuit . This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.

Section titled “Is F5 always a defrost sensor failure? F5 most commonly indicates a defrost sensor or defrost thermostat fault. However, a broken wire in the harness connecting these components to the control board produces the same symptom. Always inspect the wiring connectors at the defrost sensor and thermostat locations before ordering replacement parts. Reference: Whirlpool official support documentation (whirlpool.com/support) and authorized service guides ### Is it safe to keep using my Whirlpool WRS325SDHZ with error F5? If error F5 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the refrigerator with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error F5 on a Whirlpool WRS325SDHZ? Repair costs for error F5 on the Whirlpool WRS325SDHZ refrigerator depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Whirlpool-authorized service provider for an accurate estimate based on your specific situation. ### What does error code F5 mean on a Whirlpool refrigerator? Error code F5 on Whirlpool refrigerator models indicates Defrost sensor failure — the freezer defrost sensor or defrost thermostat has failed or its circuit . This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.”