Skip to content
Appliance Error Codes

What Does F1 Error Mean on Whirlpool WRS325SDHZ?

Error F1 on Whirlpool WRS325SDHZ: Ice maker sensor failure — ice maker thermistor has failed or its circuit is ope. Follow the troubleshooting steps below to diagnose and fix this refrigerator issue. The F1 error code on your Whirlpool refrigerator indicates a fault with the ice maker thermistor — the temperature sensor inside the ice maker assembly. This sensor monitors temperatures during ice production. A power reset is the first step. If F1 persists, the ice maker thermistor or its wiring requires service. ## What Does F1 Mean? The ice maker thermistor is a small temperature sensor mounted inside the ice maker module that monitors the temperature of the ice mold during filling and freezing cycles. It sends resistance readings to the main control board. When temperatures reach the correct freeze point, the control board triggers the ice harvest cycle. When the thermistor fails or its circuit is open (broken wire), the control board cannot verify that ice has frozen completely. Rather than harvest ice that may be only partially frozen, the control board halts ice production and displays F1. On models like the WRS325SDHZ and WRX735SDHZ, the ice maker is located in the upper door or upper shelf area of the freezer. The thermistor is a component of the ice maker module and is typically replaced as part of the module assembly rather than individually. ## Possible Causes 1. Faulty ice maker thermistor with a resistance value outside the normal operating range 2. Open circuit in the wiring between the thermistor and the main control board 3. Loose wiring connector at the ice maker module 4. Ice maker module failure affecting the thermistor circuit 5. Extremely cold freezer temperatures from a separate fault causing the thermistor to read out of range ## Troubleshooting Steps | Step | Action | Expected Result | |------|--------|-----------------| | 1 | Turn off the ice maker using the control panel ice maker off switch, wait 1 minute, then turn it back on | Ice maker restarts — F1 clears and production resumes normally | | 2 | Perform a full refrigerator power reset by unplugging for 10 minutes or switching off the circuit breaker | F1 does not return after power-cycle — fault was temporary | | 3 | If F1 persists, check the wiring connector where the ice maker harness connects to the refrigerator wiring system — often accessible at the top of the freezer compartment | Connector is secure with no damage — wiring fault ruled out | | 4 | If wiring is intact and F1 continues, schedule service for ice maker thermistor testing and module replacement | Technician confirms thermistor fault and replaces ice maker module | An F1 code affects only the ice maker and does not impact food storage temperatures. Food in the refrigerator and freezer remains safe. You may continue using the refrigerator normally while the ice maker is being serviced. ## When to Call a Technician Contact Whirlpool authorized service if: - F1 returns immediately after turning the ice maker back on or power cycling the refrigerator

  • Ice maker has not produced ice in 24 hours or more
  • Ice maker makes clicking sounds but the mold does not fill with water Professional repair costs for F1 issues typically range from $80 to $200 depending on the specific component and your service region. ## Frequently Asked Questions ### Will the F1 code affect my refrigerator or freezer cooling? No. F1 is specific to the ice maker thermistor circuit and does not affect the main refrigerator or freezer cooling systems. Food storage temperatures remain normal. Only ice production is affected.

Can I reset the ice maker on my Whirlpool refrigerator to clear F1? Yes, switching the ice maker off for one minute using the ice maker control switch, then switching it back on, is equivalent to a reset. Some Whirlpool models also have a small reset button on the ice maker module itself. If F1 clears after the reset and ice production resumes, the fault was likely a temporary sensor reading.

Section titled “Can I reset the ice maker on my Whirlpool refrigerator to clear F1? Yes, switching the ice maker off for one minute using the ice maker control switch, then switching it back on, is equivalent to a reset. Some Whirlpool models also have a small reset button on the ice maker module itself. If F1 clears after the reset and ice production resumes, the fault was likely a temporary sensor reading.”

Is the ice maker thermistor the same as the freezer temperature sensor? No. The ice maker thermistor is specific to the ice maker module and monitors mold temperature during ice production. The freezer temperature sensor (F7 or F8 code) is a separate component that monitors the overall freezer compartment temperature. Both are thermistors but they are in different locations and serve different functions.

Section titled “Is the ice maker thermistor the same as the freezer temperature sensor? No. The ice maker thermistor is specific to the ice maker module and monitors mold temperature during ice production. The freezer temperature sensor (F7 or F8 code) is a separate component that monitors the overall freezer compartment temperature. Both are thermistors but they are in different locations and serve different functions.”

How do I know if my Whirlpool ice maker module needs replacement? If F1 persists after a power reset and the wiring is confirmed intact, the ice maker thermistor has likely failed. Since the thermistor is typically integrated into the ice maker module assembly, replacing the complete module is usually the most cost-effective repair. A technician can confirm with a resistance test on the thermistor terminals. Reference: Whirlpool official support documentation (whirlpool.com/support) and authorized service guides ### Is it safe to keep using my Whirlpool WRS325SDHZ with error F1? If error F1 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the refrigerator with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error F1 on a Whirlpool WRS325SDHZ? Repair costs for error F1 on the Whirlpool WRS325SDHZ refrigerator depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Whirlpool-authorized service provider for an accurate estimate based on your specific situation. ### What does error code F1 mean on a Whirlpool refrigerator? Error code F1 on Whirlpool refrigerator models indicates Ice maker sensor failure — ice maker thermistor has failed or its circuit is open. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.

Section titled “How do I know if my Whirlpool ice maker module needs replacement? If F1 persists after a power reset and the wiring is confirmed intact, the ice maker thermistor has likely failed. Since the thermistor is typically integrated into the ice maker module assembly, replacing the complete module is usually the most cost-effective repair. A technician can confirm with a resistance test on the thermistor terminals. Reference: Whirlpool official support documentation (whirlpool.com/support) and authorized service guides ### Is it safe to keep using my Whirlpool WRS325SDHZ with error F1? If error F1 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the refrigerator with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error F1 on a Whirlpool WRS325SDHZ? Repair costs for error F1 on the Whirlpool WRS325SDHZ refrigerator depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Whirlpool-authorized service provider for an accurate estimate based on your specific situation. ### What does error code F1 mean on a Whirlpool refrigerator? Error code F1 on Whirlpool refrigerator models indicates Ice maker sensor failure — ice maker thermistor has failed or its circuit is open. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.”