Skip to content
Appliance Error Codes

Error Code E2 on Toshiba AW-DUK1300KS Washer | Causes & Fix

Error E2 on Toshiba : Door or lid not closed — lid switch or door lock fault. Follow the troubleshooting steps below to diagnose and fix this washer issue. ## What Error Code E2 Means on a Toshiba AW-DUK1300KS E2 indicates the main control board cannot confirm the lid is securely closed. Toshiba top-load washers use a magnetic lid switch or mechanical lid-lock switch. If the switch does not confirm closure, the board will not allow agitation or spin. The lid switch is a safety interlock that prevents the drum from moving while the lid is open. Toshiba AW-series models use either a magnetic reed switch (where a lid-mounted magnet activates a rim-mounted switch) or a mechanical microswitch (where a tab on the lid depresses a switch button in the cabinet). Magnetic switches can fail when the lid magnet falls out or the reed switch contacts wear. Mechanical switches fail when the actuator tab breaks or the switch contacts deteriorate. Both types are low-cost replacement parts available from Toshiba authorised suppliers and are a straightforward DIY repair requiring only a Phillips screwdriver. ## Symptoms - E2 on the display panel

  • Cycle paused or halted mid-programme
  • Drum not rotating or water not draining/filling as expected ## Common Causes - Lid not fully latched (foreign object preventing closure)
  • Lid switch magnet missing or displaced
  • Lid switch/sensor wiring harness loose or broken
  • Lid switch mechanism damaged ## Tools You May Need - digital multimeter
  • Phillips screwdriver
  • flat-head screwdriver ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Open and firmly close the lid — listen for a positive click. Remove any foreign objects preventing full closure. | Lid closed. | | 2 | Unplug the washer. Inspect the lid hinge area and switch actuator for visible damage. | Physical inspection completed. | | 3 | Locate the lid switch (two wires at the lid hinge). Disconnect and test continuity — lid closed: ~0 Ω; lid open: OL. | Continuity result confirmed. | | 4 | Replace the lid switch assembly if it fails the continuity test. | Lid switch replaced. | | 5 | Restore power, close the lid, and start a wash programme to confirm E2 clears. | E2 cleared. | ## Safety Precautions Always unplug the washer before testing or replacing the lid switch. Do not bypass the lid switch — it prevents the drum from spinning with the lid open. ## When to Call a Technician Contact a Toshiba authorised service technician if: the fault persists after replacing the identified component; if PCB-level or refrigerant-circuit work is required; or if you are not comfortable working with electrical components. ## Frequently Asked Questions ### Is it safe to keep using my Toshiba with error E2? If error E2 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E2 on a Toshiba ? Repair costs for error E2 on the Toshiba washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Toshiba-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E2 mean on a Toshiba washer? Error code E2 on Toshiba washer models indicates Door or lid not closed — lid switch or door lock fault. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Toshiba with error E2? If error E2 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E2 on a Toshiba ? Repair costs for error E2 on the Toshiba washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Toshiba-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E2 mean on a Toshiba washer? Error code E2 on Toshiba washer models indicates Door or lid not closed — lid switch or door lock fault. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.