Skip to content
Appliance Error Codes

Error Code E1 on Toshiba DW-14F2MESS Dishwasher | Causes & Fix

Error E1 on Toshiba : Water fill fault — machine did not reach the required water level in time. Follow the troubleshooting steps below to diagnose and fix this dishwasher issue. ## What Error Code E1 Means on a Toshiba DW-14F2MESS E1 indicates the dishwasher failed to fill to the required water level within the programmed fill timeout. E1 is raised if the flow meter does not register the expected pulse count within 4 minutes, or the water level pressure switch does not confirm fill within the allowed time. Confirmed from Toshiba DW-14F1ME and DW-14F2MESS official manuals (ManualsLib). On DW-series models the inlet solenoid valve is a 24 V AC coil energised by the main PCB relay at the start of each fill phase and at the beginning of each rinse phase. An intermittent E1 that appears only on the first cycle of the day usually reflects low overnight water supply pressure rather than a faulty component. Confirm household pressure is within the specified 30 to 1000 kPa range before replacing the inlet valve. ## Symptoms - E1 displayed on the digital panel

  • Wash cycle paused or halted
  • No water entering, no draining, or no heating as expected ## Common Causes - Water supply tap closed or water pressure too low (<30 kPa)
  • Inlet hose kinked or blocked
  • Inlet solenoid valve failed (OL winding)
  • Flow meter sensor fault
  • Water supply temporarily interrupted ## Tools You May Need - digital multimeter
  • Phillips screwdriver
  • adjustable wrench ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Confirm the water supply tap beneath the sink is fully open and the water pressure is at least 30 kPa. | Water supply confirmed. | | 2 | Inspect the inlet hose for kinks. Disconnect from the dishwasher inlet and confirm water flows freely when the tap is opened. | Inlet hose confirmed clear. | | 3 | Unplug the dishwasher. Disconnect the inlet valve solenoid harness and measure coil resistance — expected 3,500–5,000 Ω. OL indicates a failed valve. | Inlet valve resistance measured. | | 4 | On the DW-14F1ME and DW-14F2MESS, remove the inlet valve and check the filter screen inside for mineral deposits. Clean if present. | Inlet filter cleaned. | | 5 | Restore power and run a Normal wash cycle. Confirm E1 does not recur. | E1 cleared. | ## Safety Precautions Turn off the water supply tap before disconnecting any inlet hose. Have a towel ready — residual water will drain from the hose. Unplug the dishwasher before testing the solenoid valve. ## When to Call a Technician Contact a Toshiba authorised service technician if: the fault persists after replacing the identified component; if PCB-level or refrigerant-circuit work is required; or if you are not comfortable working with electrical components. ## Frequently Asked Questions ### Is it safe to keep using my Toshiba with error E1? If error E1 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E1 on a Toshiba ? Repair costs for error E1 on the Toshiba dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Toshiba-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E1 mean on a Toshiba dishwasher? Error code E1 on Toshiba dishwasher models indicates Water fill fault — machine did not reach the required water level in time. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Toshiba with error E1? If error E1 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E1 on a Toshiba ? Repair costs for error E1 on the Toshiba dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Toshiba-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E1 mean on a Toshiba dishwasher? Error code E1 on Toshiba dishwasher models indicates Water fill fault — machine did not reach the required water level in time. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.