Skip to content
Appliance Error Codes

Error Code E1 on Sharp SJ-XE624F Refrigerator | Causes & Fix

Error E1 on Sharp : Refrigerator compartment NTC temperature sensor open or short circuit. Follow the troubleshooting steps below to diagnose and fix this refrigerator issue. ## What Error Code E1 Means on a Sharp SJ-XE624F Refrigerator The E1 error code on the Sharp SJ-XE624F (624 L French Door Bottom-Freezer Refrigerator) indicates: Refrigerator compartment NTC temperature sensor open or short circuit. Sharp SJ-series refrigerators continuously monitor NTC temperature sensors, fan motors, the defrost circuit, and PCB communication links. When any parameter falls outside the normal operating envelope, the control board stores the fault and displays the corresponding error code on the digital panel. ## Symptoms - E1 displayed on the refrigerator panel or temperature display

  • Cooling performance reduced or stopped
  • Audible alarm (beeping) accompanying the code
  • Display reverts to fault code after each power cycle until repaired ## Common Causes - NTC thermistor open or short-circuited (typical 10 kΩ @ 25 °C)
  • Loose or corroded connector on the sensor harness
  • Sensor lead wire chafed against cabinet metalwork
  • Main PCB sensor input circuit failed ## Tools You May Need - digital multimeter
  • Phillips screwdriver
  • flat-head screwdriver
  • plastic panel clips tool
  • isopropyl alcohol (for connector cleaning) ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Power off the refrigerator at the wall outlet. | Unit is de-energised. | | 2 | Locate the fridge compartment NTC sensor (typically clipped to the evaporator cover or air duct). | Sensor identified. | | 3 | Disconnect the sensor connector. Measure resistance across sensor terminals with a multimeter. Expected ~10 kΩ at 25 °C; open circuit (∞) or short (0 Ω) indicates failure. | Sensor condition known. | | 4 | Inspect the harness for chafing, kinking, or corrosion. Reseat the connector firmly. | Harness condition checked. | | 5 | If sensor resistance is out of range, replace the NTC thermistor. Restore power and verify E1 is cleared. | Fault resolved or escalated. | ## Safety Precautions Before performing any internal diagnostics on a Sharp SJ-XE624F refrigerator, unplug the power cord from the wall outlet and wait at least 3 minutes for capacitors to discharge. Do not work on the sealed refrigerant circuit unless you are a licensed refrigerant handler — R600a (isobutane) used in many SJ-series models is flammable. Ensure adequate ventilation and eliminate ignition sources before opening any refrigerant lines. Wear insulated gloves when handling electrical components. ## When to Call a Technician Call a qualified appliance technician if: - the sealed refrigerant circuit requires inspection, leak testing, or recharging
  • the compressor or inverter drive module requires replacement
  • the main PCB requires replacement
  • the fault persists after replacing the suspect sensor or harness ## Preventing Future Faults - ensure the refrigerator has at least 5 cm clearance on all sides for ventilation
  • clean the condenser grille annually with a vacuum or brush
  • avoid placing hot food directly in the refrigerator to reduce thermal stress on sensors
  • check door seals regularly for cracks or gaps that reduce cooling efficiency
  • schedule a professional service check every 2–3 years for inverter-equipped models ## Frequently Asked Questions ### Is it safe to keep using my Sharp with error E1? If error E1 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the refrigerator with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E1 on a Sharp ? Repair costs for error E1 on the Sharp refrigerator depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Sharp-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E1 mean on a Sharp refrigerator? Error code E1 on Sharp refrigerator models indicates Refrigerator compartment NTC temperature sensor open or short circuit. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Sharp with error E1? If error E1 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the refrigerator with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E1 on a Sharp ? Repair costs for error E1 on the Sharp refrigerator depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Sharp-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E1 mean on a Sharp refrigerator? Error code E1 on Sharp refrigerator models indicates Refrigerator compartment NTC temperature sensor open or short circuit. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.