Skip to content
Appliance Error Codes

Error Code E6 on Sharp KD-GHH8S7GW9 Dryer | Causes & Fix

Error E6 on Sharp : Temperature NTC sensor fault — inlet or outlet sensor open or short circuit. Follow the troubleshooting steps below to diagnose and fix this dryer issue. ## What Error Code E6 Means on a Sharp KD-GHH8S7GW9 Dryer The E6 error code on the Sharp KD-GHH8S7GW9 (8 kg Heat Pump Condenser Dryer (UK/EU)) indicates: Temperature NTC sensor fault — inlet or outlet sensor open or short circuit. Sharp dryers and washer-dryer combos monitor the door lock, drum rotation, heating circuit, temperature sensors, and drain system throughout every drying programme. When a subsystem fails to operate within normal parameters, the control board stops the cycle and displays the fault code. ## Symptoms - E6 displayed on the control panel

  • Cycle paused or stopped
  • Drum may still be warm depending on cycle stage
  • Audible alarm may accompany the error ## Common Causes - Inlet or exhaust NTC thermistor open-circuited or short-circuited
  • Sensor connector loose or corroded on sensor harness
  • Sensor lead wire damaged by heat or pinching
  • PCB NTC sensor input circuit failed ## Tools You May Need - digital multimeter
  • Phillips screwdriver
  • flat-head screwdriver
  • capacitance meter (for capacitor testing)
  • isopropyl alcohol (for connector cleaning) ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Unplug the dryer. Locate the NTC temperature sensor — typically mounted in the air inlet duct or on the heating element housing. | Sensor located. | | 2 | Disconnect the sensor connector. Measure resistance with a multimeter at room temperature (20–25 °C). Expected: ~10 kΩ. Open or shorted reading indicates sensor failure. | Sensor resistance measured. | | 3 | Inspect the sensor harness and connector for heat damage, chafing, or corrosion. Clean corrosion with isopropyl alcohol and reseat the connector. | Harness inspected. | | 4 | If resistance is out of range, replace the NTC sensor with the OEM Sharp part for your model. | Sensor replaced. | | 5 | Restore power and run a short drying cycle. Verify E6 is cleared and the drum heats correctly. | Repair verified. | ## Safety Precautions Always unplug the Sharp KD-GHH8S7GW9 from the wall outlet before opening any panel or touching internal components. For heat pump dryers (KD-series) the refrigerant circuit contains pressurised R290 or R134a — do not open or modify the refrigerant circuit without a refrigerant handling licence. The drum motor and heating element capacitors can retain electrical charge for several minutes after power removal; wait at least 3 minutes before handling capacitors. Keep all heat sources, sparks, and open flames well away from the appliance during any repair. ## When to Call a Technician Contact a qualified appliance technician if: - the drum bearings require replacement
  • the motor or motor inverter board has failed
  • the heat pump compressor or refrigerant circuit requires service (KD-series)
  • the main PCB requires replacement ## Preventing Future Faults - clean the lint filter after every single drying cycle without exception
  • clean the condenser coil (heat pump models) every 2 months using the machine’s self-clean programme
  • do not overdry — use sensor-dry programmes where available
  • ensure the exhaust vent (vented models) is free of obstructions, lint build-up, and kinks
  • leave the door slightly ajar after each cycle to ventilate the drum and drum seal ## Frequently Asked Questions ### Is it safe to keep using my Sharp with error E6? If error E6 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dryer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E6 on a Sharp ? Repair costs for error E6 on the Sharp dryer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Sharp-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E6 mean on a Sharp dryer? Error code E6 on Sharp dryer models indicates Temperature NTC sensor fault — inlet or outlet sensor open or short circuit. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Sharp with error E6? If error E6 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dryer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E6 on a Sharp ? Repair costs for error E6 on the Sharp dryer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Sharp-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E6 mean on a Sharp dryer? Error code E6 on Sharp dryer models indicates Temperature NTC sensor fault — inlet or outlet sensor open or short circuit. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.