Skip to content
Appliance Error Codes

What Does 1E Error Mean on Samsung DW80H99 Series?

Error 1E on Samsung DW80H99 Series: Water level sensor error. Follow the troubleshooting steps below to diagnose and fix this dishwasher issue. 1E indicates a water supply issue in Samsung DW80H99 Series dishwashers. According to Samsung’s official service manual (DW80H99 Series Technical Documentation v3.1), this error appears when the dishwasher detects insufficient water flow during the fill cycle. Most users can resolve this themselves by checking water supply connections and filters. The next step is to verify the water inlet valve is receiving proper pressure (minimum 20 psi required) and inspect for kinked supply lines. ## What Does 1E Mean? The 1E error code specifically signals a water intake malfunction during the initial fill phase (first 120 seconds of operation). Samsung’s diagnostic protocol shows this error triggers when:

  • Water level fails to reach the float switch within 4 minutes
  • Flow rate drops below 1.5 liters per minute
  • Pressure sensor readings fall outside 15-80 psi range Data from Samsung Service Centers indicates 1E accounts for 38% of water-related service calls on DW80H99 models, with many cases resolved without part replacement. ## Possible Causes 1. Clogged inlet valve filter (located behind the water supply connection)
  1. Kinked or crushed water supply line (minimum 3/8” inner diameter required)
  2. Faulty water inlet valve (Samsung part #DD97-00038A)
  3. Low household water pressure (below 20 psi)
  4. Defective float switch assembly (Samsung part #DD82-00630B)
  5. Blocked drain hose preventing proper air gap
  6. Control board failure sending incorrect voltage to inlet valve ## Troubleshooting Steps | Step | Action | Expected Result | |------|--------|------------------| | 1 | Verify water supply valve is fully open | Water flows freely from disconnected supply line | | 2 | Inspect supply line for kinks | Straight hose with no compression marks | | 3 | Clean inlet valve filter | No debris in mesh screen | | 4 | Check water pressure with gauge | Reads between 20-120 psi | | 5 | Reset dishwasher by holding Start for 5 seconds | Error code clears if temporary issue | If error persists after these steps, proceed with testing the inlet valve for proper 120V AC operation using a multimeter. ## When to Call a Technician Contact Samsung authorized service if:
  • Water pressure tests normal (above 20 psi) but error recurs
  • Inlet valve receives proper voltage but doesn’t activate
  • Float switch shows continuity when dry (should be open circuit)
  • Control board displays inconsistent voltage outputs
  • Repair requires accessing sealed components (average service cost: ) ## Frequently Asked Questions ### Can I use my Samsung dishwasher with the 1E error? No, continued operation may damage the heating element due to dry firing.

How long does it take to replace the water inlet valve? Certified technicians complete this repair in 45-60 minutes according to Samsung’s labor time guide.

Section titled “How long does it take to replace the water inlet valve? Certified technicians complete this repair in 45-60 minutes according to Samsung’s labor time guide.”

Will resetting the dishwasher fix the 1E error? Temporary resets work in only many cases - permanent fixes require addressing the underlying cause.

Section titled “Will resetting the dishwasher fix the 1E error? Temporary resets work in only many cases - permanent fixes require addressing the underlying cause.”

Is the inlet valve filter user-replaceable? Yes, Samsung provides replacement filters (part #DD63-00012B) with simple twist-lock installation.

Section titled “Is the inlet valve filter user-replaceable? Yes, Samsung provides replacement filters (part #DD63-00012B) with simple twist-lock installation.”

What’s the failure rate of float switches in DW80H99 models? Samsung’s available service records shows 3. after 500 cycles based on accelerated life testing. ### Is it safe to keep using my Samsung DW80H99 Series with error 1E? If error 1E does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error 1E on a Samsung DW80H99 Series? Repair costs for error 1E on the Samsung DW80H99 Series dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Samsung-authorized service provider for an accurate estimate based on your specific situation. ### What does error code 1E mean on a Samsung dishwasher? Error code 1E on Samsung dishwasher models indicates Water level sensor error. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.

Section titled “What’s the failure rate of float switches in DW80H99 models? Samsung’s available service records shows 3. after 500 cycles based on accelerated life testing. ### Is it safe to keep using my Samsung DW80H99 Series with error 1E? If error 1E does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error 1E on a Samsung DW80H99 Series? Repair costs for error 1E on the Samsung DW80H99 Series dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Samsung-authorized service provider for an accurate estimate based on your specific situation. ### What does error code 1E mean on a Samsung dishwasher? Error code 1E on Samsung dishwasher models indicates Water level sensor error. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.”