Skip to content
Appliance Error Codes

Error Code H87 on Panasonic NH-P100S1 Dryer | Causes & Fix

Error H87 on Panasonic : Heating did not complete within the cycle time — heat-pump circuit underperformi. Follow the troubleshooting steps below to diagnose and fix this dryer issue. ## What Error Code H87 Means on a Panasonic NH-P100S1 Dryer The H87 error code on the Panasonic NH-P100S1 heat-pump dryer indicates a heat-pump circuit underperforming. Panasonic NH-series heat-pump dryers use dual NTC temperature sensors, an inverter-driven compressor, and a separate door interlock system to manage safe drying cycles. When any parameter falls outside the acceptable range, the dryer halts and displays the fault code on the panel. ## Symptoms - H87 after extended drying cycle

  • clothes still damp at end of maximum cycle time
  • machine runs full cycle time without finishing
  • H87 in high-humidity room ## Common Causes - condenser filter airflow restriction — heat exchange efficiency reduced
  • drum overloaded — excess moisture extends drying time
  • ambient humidity above 75% — moisture extraction difficult
  • heat-pump refrigerant charge slightly low ## Tools You May Need - multimeter
  • Phillips screwdriver
  • flat-head screwdriver
  • soft brush or vacuum (for condenser filter cleaning) ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Clean the lint filter and condenser filter thoroughly (U02 procedure) | Check complete | | 2 | Reduce the load size — overloading slows drying and can cause H87 on a marginal heat-pump | Check complete | | 3 | Confirm room temperature is above 5°C and relative humidity is reasonable (below 75%) | Check complete | | 4 | Allow the dryer to cool for 20 minutes, then retry with a smaller load | Check complete | | 5 | If H87 persists on small correct loads with clean filters, the heat-pump refrigerant circuit is underperforming — contact a Panasonic service technician | Check complete | ## Safety Precautions Always unplug the dryer before removing any panels or accessing internal components. Do not attempt to open or service the sealed heat-pump refrigerant circuit without refrigeration certification — this is a legal requirement in most jurisdictions. The heat-pump compressor remains warm for several minutes after shutdown — allow it to cool before touching internal components. Keep all connector work in a dry environment away from condensate drainage points. ## When to Call a Technician Call a qualified appliance technician if: - the heat-pump compressor or refrigerant circuit requires assessment (H96)
  • the main control PCB requires replacement
  • the drum bearing requires replacement (full disassembly required)
  • the error persists after all user-accessible checks have been completed ## Preventing Future Faults - clean the primary lint filter after every drying cycle
  • clean the condenser heat-pump filter every 10–20 cycles
  • empty the condensate drawer after every cycle
  • operate in ambient temperatures between 5°C and 35°C
  • do not overload the drum beyond 70% of rated capacity ## Frequently Asked Questions ### Is it safe to keep using my Panasonic with error H87? If error H87 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dryer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error H87 on a Panasonic ? Repair costs for error H87 on the Panasonic dryer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Panasonic-authorized service provider for an accurate estimate based on your specific situation. ### What does error code H87 mean on a Panasonic dryer? Error code H87 on Panasonic dryer models indicates Heating did not complete within the cycle time — heat-pump circuit underperforming. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Panasonic with error H87? If error H87 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dryer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error H87 on a Panasonic ? Repair costs for error H87 on the Panasonic dryer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Panasonic-authorized service provider for an accurate estimate based on your specific situation. ### What does error code H87 mean on a Panasonic dryer? Error code H87 on Panasonic dryer models indicates Heating did not complete within the cycle time — heat-pump circuit underperforming. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.