Skip to content
Appliance Error Codes

What Does F3 Error Mean on LG LSGL6335F?

Error F3 on LG LSGL6335F: Touchpad key shorted or stuck — a control panel key has been continuously activa. Follow the troubleshooting steps below to diagnose and fix this range issue. The F3 error code on your LG LSGL6335F range indicates the control board has detected a key on the touchpad that has been continuously activated for more than 60 seconds. Like the Samsung SE error, this is caused by moisture under the control panel, a physically stuck key, or a failed touchpad membrane. Trip the circuit breaker for 5 minutes and thoroughly dry the control panel before investigating further. ## What Does F3 Mean? The F3 error on the LSGL6335F appears when the control board’s key-scan circuit detects one key sending a continuous activation signal — something that cannot happen through normal use. The most common trigger is moisture from steam or cleaning liquid seeping under the touchpad membrane and creating a persistent short between two contact pads. On the LSGL6335F, the control panel is mounted on the front of the range. Steam from boiling pots on the rear burners can rise and condense behind the knob trim or around the touchpad edge. Over time, mineral deposits from this moisture can create conductive bridges that trigger F3 even after the moisture has dried. F3 can also be triggered by a physically jammed key — if a key becomes stuck in the pressed position due to food debris or worn membrane, the board registers it as a 60-second hold. ## Possible Causes 1. Moisture from steam or cleaning liquids trapped under or behind the touchpad membrane 2. Physically stuck or jammed touchpad key that cannot return to the neutral position 3. Worn or failed touchpad membrane switch panel 4. Damaged flat ribbon cable between the touchpad PCB and the main control board 5. Failed main control board key-scanning circuit ## Troubleshooting Steps | Step | Action | Expected Result | |------|--------|-----------------| | 1 | Trip the circuit breaker for the LSGL6335F to the full OFF position and leave off for 5 minutes; while waiting, wipe the entire control panel with a dry cloth to remove all moisture and grease | Control panel is dry and fully reset | | 2 | Restore power; if F3 does not return, moisture was the cause; monitor during subsequent cooking | F3 does not return — moisture was the cause | | 3 | If F3 returns, power down again and press each button firmly at center to attempt to free any physically stuck key; also try pressing off-center | All keys depress and spring back freely | | 4 | If a key remains stuck and cannot be freed, remove the control panel cover to access the touchpad membrane; inspect for visible moisture damage, burns, or a stuck actuator pad | Touchpad membrane condition is assessed | | 5 | Clean the ribbon cable connector contacts with 90% isopropyl alcohol on a lint-free cloth; reseat the ribbon cable firmly at both ends | Ribbon cable is clean and fully seated | | 6 | If cleaning and reseating do not clear F3, replace the touchpad membrane panel; if F3 persists after a new membrane, replace the main control board | F3 clears after new membrane or board is installed | LG advises not using the range while F3 is active, as the control board may interpret the stuck key as a sustained START command and attempt to activate heating elements. ## When to Call a Technician Contact LG authorized service if: - F3 persists after replacing the touchpad membrane — the ribbon cable or main board requires replacement

  • Visible burn marks are found on the touchpad or ribbon cable connectors Professional repair costs for F3 issues typically range from $80 to $220 depending on the specific component and your service region. ## Frequently Asked Questions ### Why does my LG range show F3 when I have not pressed any buttons? F3 can appear without any physical key press when moisture under the touchpad creates a conductive short between contact pads. The control board cannot distinguish between a physical key press and a moisture-caused short. Steam from boiling pots, condensation in humid environments, and cleaning liquid applied to the control panel are the most common sources of this moisture.

Can I clear the F3 error by pressing a specific button? You can attempt to clear F3 by pressing CLEAR/OFF or by performing a circuit breaker reset. However, if the underlying cause is moisture or a physically stuck key, F3 will return because the condition causing it has not been resolved. The reset only clears the displayed code — it does not fix the shorted key circuit.

Section titled “Can I clear the F3 error by pressing a specific button? You can attempt to clear F3 by pressing CLEAR/OFF or by performing a circuit breaker reset. However, if the underlying cause is moisture or a physically stuck key, F3 will return because the condition causing it has not been resolved. The reset only clears the displayed code — it does not fix the shorted key circuit.”

Is the F3 code dangerous on my LG range? F3 presents a safety concern because the control board may interpret the stuck key as a sustained START command. This could cause heating elements to activate unexpectedly. Turn off the range at the circuit breaker when F3 is active and do not leave the range unattended until the issue is resolved.

Section titled “Is the F3 code dangerous on my LG range? F3 presents a safety concern because the control board may interpret the stuck key as a sustained START command. This could cause heating elements to activate unexpectedly. Turn off the range at the circuit breaker when F3 is active and do not leave the range unattended until the issue is resolved.”

How do I clean the LG {model_display} control panel without causing F3? Use a barely damp cloth wrung out well — never spray cleaner directly on the control panel. Apply cleaning solution to the cloth first, then wipe the panel. Immediately follow with a dry cloth to absorb all moisture. Avoid cleaning the control panel while the range is hot, as steam from the oven can pull liquid under the touchpad edge. Reference: LG official support documentation (lg.com/us/support) and authorized service guides ### Is it safe to keep using my LG LSGL6335F with error F3? If error F3 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the range with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error F3 on a LG LSGL6335F? Repair costs for error F3 on the LG LSGL6335F range depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a LG-authorized service provider for an accurate estimate based on your specific situation. ### What does error code F3 mean on a LG range? Error code F3 on LG range models indicates Touchpad key shorted or stuck — a control panel key has been continuously activated for more than 60. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.

Section titled “How do I clean the LG {model_display} control panel without causing F3? Use a barely damp cloth wrung out well — never spray cleaner directly on the control panel. Apply cleaning solution to the cloth first, then wipe the panel. Immediately follow with a dry cloth to absorb all moisture. Avoid cleaning the control panel while the range is hot, as steam from the oven can pull liquid under the touchpad edge. Reference: LG official support documentation (lg.com/us/support) and authorized service guides ### Is it safe to keep using my LG LSGL6335F with error F3? If error F3 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the range with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error F3 on a LG LSGL6335F? Repair costs for error F3 on the LG LSGL6335F range depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a LG-authorized service provider for an accurate estimate based on your specific situation. ### What does error code F3 mean on a LG range? Error code F3 on LG range models indicates Touchpad key shorted or stuck — a control panel key has been continuously activated for more than 60. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.”