Skip to content
Appliance Error Codes

What Does FE Error Mean on LG LDPH7972S?

Error FE on LG LDPH7972S: Water overfill detected - excess water in tub. Follow the troubleshooting steps below to diagnose and fix this dishwasher issue. The FE error code on your LG LDPH7972S dishwasher indicates that the unit has detected an overfill condition, meaning more water has entered the tub than expected. The drain pump automatically activates when this error appears to remove excess water. Stop the cycle immediately and check whether you used the correct type of detergent. ## What Does FE Mean? The FE error code stands for “Fill Error” and triggers when the LG LDPH7972S detects that the water level in the tub exceeds the normal operating range. The dishwasher continuously monitors water levels during the fill and wash phases, and if the level rises above the maximum threshold, the control board activates the drain pump and displays the FE code. On the LDPH7972S, overfill conditions can occur for several reasons. The most common is using regular hand-washing dish soap instead of automatic dishwasher detergent, which creates excessive foam that the water level sensor misinterprets as a high water level. The second most common cause is a water inlet valve that fails to close properly after the fill cycle completes. The LDPH7972S features TrueSteam technology that uses real steam to sanitize dishes and remove baked-on food residue. QuadWash Pro enhances spray coverage with multi-motion arms, while Dynamic Heat Dry circulates heated air for thorough drying. The overfill protection system operates independently of these features and will override any active wash program when triggered. A stuck relay on the electronic control board can also cause the FE error by keeping the water inlet valve energized continuously, allowing water to fill beyond the normal level. This condition requires professional repair as it involves an electronic component failure. ## Possible Causes 1. Regular hand-washing dish soap used instead of automatic dishwasher detergent, causing excessive suds 2. Dishwasher not properly leveled, causing uneven water distribution that triggers the overfill sensor 3. Water inlet valve stuck in the open position due to a mechanical or electrical failure 4. Door not properly aligned, allowing water to contact sensors in unintended areas 5. Stuck relay on the electronic control board keeping the inlet valve energized 6. Previous cycle interrupted during fill phase, leaving residual water that compounds during the next fill 7. Faulty water level pressure sensor giving incorrect readings to the control board ## Troubleshooting Steps | Step | Action | Expected Result | |------|--------|-----------------| | 1 | Cancel the current cycle and allow the drain pump to remove excess water from the tub | Water level drops to normal or tub empties completely | | 2 | Open the door and check for excessive suds or foam in the tub | Tub shows normal water without excessive foam | | 3 | Verify your detergent is specifically labeled for automatic dishwashers, not hand-washing liquid | Detergent is correct type for dishwasher use | | 4 | Place a level on top of the dishwasher and adjust leveling feet as needed | Unit is level in both front-to-back and side-to-side directions | | 5 | Power cycle the dishwasher by turning off the circuit breaker for 60 seconds, then turning it back on | Display resets and no error code appears on startup | | 6 | Run a short rinse cycle to verify the fill level returns to normal | Water fills to the correct level and stops without triggering FE | LG recommends not opening the dishwasher door during an active FE error until the drain pump has finished removing excess water. Opening the door while the tub is overfilled may cause water to spill onto the floor. Always confirm the drain pump has stopped running before opening the door. ## When to Call a Technician Contact LG authorized service if: - The FE error occurs repeatedly even when using the correct dishwasher detergent

  • You hear the water inlet valve running continuously after the fill cycle should have ended
  • The tub fills to an abnormally high level before the error code appears
  • Power cycling the unit does not resolve the FE error
  • Water continues to enter the tub even when the dishwasher is in standby mode Professional repair costs for FE issues typically range from $120 to $350 depending on the specific component that needs replacement and your service region. ## Frequently Asked Questions ### Will the drain pump run automatically when the FE error appears? Yes. The LG LDPH7972S is designed to activate the drain pump automatically when an overfill condition is detected. This is a safety measure to prevent water from overflowing the tub and causing damage to your kitchen floor.

Can leftover suds from a previous cycle cause the FE error? Yes. If a previous cycle used too much detergent or the wrong type, residual suds can persist into subsequent cycles. Running an empty rinse cycle without any detergent can help clear remaining foam from the system.

Section titled “Can leftover suds from a previous cycle cause the FE error? Yes. If a previous cycle used too much detergent or the wrong type, residual suds can persist into subsequent cycles. Running an empty rinse cycle without any detergent can help clear remaining foam from the system.”
Section titled “Is the FE error related to the FE error on LG washing machines? While both use the same code letters, dishwasher and washing machine error codes are independent. The FE error on an LG dishwasher specifically refers to water overfill in the dishwasher tub, not a washing machine water supply issue.”

Could a faulty water inlet valve cause flooding? A water inlet valve stuck in the open position can potentially cause flooding if the overfill protection system also fails. If you notice the FE error appearing frequently, have the inlet valve inspected by a technician to prevent a more serious water damage incident. Reference: LG official support documentation (lg.com/us/support) and authorized service guides ### Is it safe to keep using my LG LDPH7972S with error FE? If error FE does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error FE on a LG LDPH7972S? Repair costs for error FE on the LG LDPH7972S dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a LG-authorized service provider for an accurate estimate based on your specific situation. ### What does error code FE mean on a LG dishwasher? Error code FE on LG dishwasher models indicates Water overfill detected - excess water in tub. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.

Section titled “Could a faulty water inlet valve cause flooding? A water inlet valve stuck in the open position can potentially cause flooding if the overfill protection system also fails. If you notice the FE error appearing frequently, have the inlet valve inspected by a technician to prevent a more serious water damage incident. Reference: LG official support documentation (lg.com/us/support) and authorized service guides ### Is it safe to keep using my LG LDPH7972S with error FE? If error FE does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error FE on a LG LDPH7972S? Repair costs for error FE on the LG LDPH7972S dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a LG-authorized service provider for an accurate estimate based on your specific situation. ### What does error code FE mean on a LG dishwasher? Error code FE on LG dishwasher models indicates Water overfill detected - excess water in tub. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.”