Skip to content
Appliance Error Codes

What Does AE Error Mean on LG LDFC2423W?

Error AE on LG LDFC2423W: Internal leak detected - float switch activated. Follow the troubleshooting steps below to diagnose and fix this dishwasher issue. The AE error code on your LG LDFC2423W dishwasher indicates that the internal leak detection system has been triggered. The dishwasher has a float switch in the base pan that activates when water accumulates outside the tub, shutting down operation to prevent water damage. Immediately check the floor around and under the dishwasher for any signs of water. ## What Does AE Mean? The AE error code means “Aqua Error” and signals that the LG LDFC2423W has detected water in the base pan beneath the main tub. Every LG dishwasher includes an overfill protection system consisting of a float switch mounted in the base pan. When water reaches this switch, the unit immediately stops all operations and activates the drain pump to remove excess water. On the LDFC2423W, the AE error is classified as high severity because it indicates water has escaped the sealed tub area. This could be caused by a door seal failure, a cracked spray arm, an internal hose disconnection, or excessive suds pushing water out of the tub during the wash cycle. The AE error is sometimes displayed alongside the E1 code on certain LG models, as both refer to the same leak detection mechanism. The float switch must physically return to its resting position before the dishwasher can resume normal operation, which typically requires the base pan to dry out. The LDFC2423W offers a convenient 1-Hour Wash and Dry cycle that completes a full wash and dry in under 60 minutes. Its front control panel design provides a clean, seamless look, and LoDecibel technology keeps noise levels low at 48 dBA. However, none of these features can operate while the AE error is active, as the safety system takes priority over all wash functions. ## Possible Causes 1. Door gasket worn, cracked, or contaminated with food debris preventing a proper seal 2. Excessive suds from using hand-washing dish soap instead of dishwasher detergent 3. Damaged or cracked spray arm allowing water to spray outside the tub area 4. Internal hose connection loose or disconnected at the pump or sump assembly 5. Unit not level, causing water to pool unevenly and overflow through the door seal 6. Water entered the Heat Dry blower area through the rinse aid cap or softening cap 7. Faulty float switch giving a false leak detection reading ## Troubleshooting Steps | Step | Action | Expected Result | |------|--------|-----------------| | 1 | Open the dishwasher door and inspect the door gasket around the entire perimeter for cracks, tears, or food debris | Gasket is clean, flexible, and free of visible damage | | 2 | Check the floor around and under the dishwasher for any puddles or moisture | Floor is dry, or you can identify the source of the leak | | 3 | Verify you are using only automatic dishwasher detergent, not hand-washing dish soap | Detergent package clearly labeled for automatic dishwashers | | 4 | Place a level on top of the dishwasher and adjust the leveling feet if the unit is not balanced | Bubble centered in both directions on the level | | 5 | Tilt the dishwasher slightly backward to allow any water in the base pan to drain toward the drain system | Water drains from the base pan and float switch resets | | 6 | Allow the base pan to dry for up to 48 hours if significant water accumulated, then restart | Dishwasher starts a cycle without triggering AE again | LG recommends disconnecting power to the dishwasher immediately when the AE error appears to prevent potential electrical hazards from water contact with internal components. Do not operate the dishwasher until the source of the leak has been identified and resolved. ## When to Call a Technician Contact LG authorized service if: - Water is actively leaking from inside the dishwasher during a cycle

  • The door gasket appears intact but the float switch continues to trigger
  • You find water in the base pan but cannot identify the source of the leak
  • The AE error appears immediately upon starting any cycle, even after the base pan has dried
  • You notice water coming from the pump area or internal hose connections Professional repair costs for AE issues typically range from $100 to $400 depending on the specific component that needs replacement and your service region. ## Frequently Asked Questions ### Is the AE error the same as the E1 error on LG dishwashers? Yes. On many LG dishwasher models, AE and E1 refer to the same leak detection condition. Both codes indicate that the float switch in the base pan has been activated by water accumulation outside the tub.

Can using the wrong detergent really cause a leak detection error? Yes. Hand-washing dish soap produces far more suds than automatic dishwasher detergent. These excessive suds can push water past the door seal and into the base pan, triggering the float switch. Always use detergent specifically labeled for automatic dishwashers.

Section titled “Can using the wrong detergent really cause a leak detection error? Yes. Hand-washing dish soap produces far more suds than automatic dishwasher detergent. These excessive suds can push water past the door seal and into the base pan, triggering the float switch. Always use detergent specifically labeled for automatic dishwashers.”

How long does it take for the base pan to dry out? LG states that the base pan may take up to 48 hours to dry completely. The float switch will remain triggered until the water level drops below the switch activation point. You can speed up drying by tilting the unit slightly and placing absorbent towels under the front.

Section titled “How long does it take for the base pan to dry out? LG states that the base pan may take up to 48 hours to dry completely. The float switch will remain triggered until the water level drops below the switch activation point. You can speed up drying by tilting the unit slightly and placing absorbent towels under the front.”

Could a cracked spray arm cause the AE error? Yes. A cracked or broken spray arm can direct water outside the tub cavity during the wash cycle, allowing water to accumulate in the base pan. Inspect both upper and lower spray arms for visible cracks, splits, or missing components. Reference: LG official support documentation (lg.com/us/support) and authorized service guides ### Is it safe to keep using my LG LDFC2423W with error AE? If error AE does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error AE on a LG LDFC2423W? Repair costs for error AE on the LG LDFC2423W dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a LG-authorized service provider for an accurate estimate based on your specific situation. ### What does error code AE mean on a LG dishwasher? Error code AE on LG dishwasher models indicates Internal leak detected - float switch activated. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.

Section titled “Could a cracked spray arm cause the AE error? Yes. A cracked or broken spray arm can direct water outside the tub cavity during the wash cycle, allowing water to accumulate in the base pan. Inspect both upper and lower spray arms for visible cracks, splits, or missing components. Reference: LG official support documentation (lg.com/us/support) and authorized service guides ### Is it safe to keep using my LG LDFC2423W with error AE? If error AE does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error AE on a LG LDFC2423W? Repair costs for error AE on the LG LDFC2423W dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a LG-authorized service provider for an accurate estimate based on your specific situation. ### What does error code AE mean on a LG dishwasher? Error code AE on LG dishwasher models indicates Internal leak detected - float switch activated. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.”