Skip to content
Appliance Error Codes

Error Code E08 on Hoover WDWL-4138LHC Washer | Causes & Fix

Error E08 on Hoover : Heating element fault — element burned out. Follow the troubleshooting steps below to diagnose and fix this washer issue. ## What Error Code E08 Means on a Hoover WDWL-4138LHC E08 on the Hoover WDWL-4138LHC washer indicates the wash heater (heating element) has failed or its circuit is open. If the heater cannot raise water temperature within the expected time, E08 is logged. On most Hoover front-loaders the heater element is a U-shaped component at the bottom of the drum. When E08 appears, the Hoover washer pauses normal operation to protect internal components from potential damage. Not every E08 fault requires a professional engineer — many are resolved through careful inspection and routine maintenance. Work through each diagnostic step below in sequence, starting with the simplest check, to identify the root cause efficiently before considering part replacement or arranging a service call. ## Symptoms - E08 on display

  • Cold water from drum mid-programme
  • Programme runs significantly longer than normal ## Common Causes - Heating element fault — element burned out ## Tools You May Need - digital multimeter
  • Torx screwdriver
  • replacement heating element ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Unplug the machine. Remove the back panel and locate the heater element at the bottom of the drum. | Element located — continue to step 2 if the issue persists. | | 2 | Disconnect the heater wiring and test resistance between the two main terminals — 20–30 Ω is typical; OL means open (failed element). | Resistance measured — continue to step 3 if the issue persists. | | 3 | Also test for continuity between each terminal and the metal element body — OL expected; 0 Ω indicates earth leakage. | Earth leakage tested — continue to step 4 if the issue persists. | | 4 | Replace the element if open-circuit or earth-leaking. Drain the machine first via the filter. | Element replaced — continue to step 5 if the issue persists. | | 5 | Reconnect wiring and run a 60 °C cotton cycle to confirm element heats correctly. | Heating confirmed — if the fault remains, contact a qualified technician. | ## Safety Precautions Always unplug and drain the machine before replacing the heating element. The element sits in the water tub — residual hot water may be present after a failed cycle. ## Estimated Repair Time and Difficulty Most washer error code E08 faults can be assessed and addressed in 30–90 minutes using the steps above. The diagnostic process requires only basic tools: a multimeter and standard screwdrivers cover the majority of checks described here. If a replacement part is required, allow 1–5 working days for delivery. A trained technician with access to the correct diagnostic equipment will typically resolve this type of fault within a single service visit. ## When to Call a Technician Contact a Hoover authorised service technician if: the fault persists after following all the steps above; if PCB-level or refrigerant-circuit work is required; or if you are not comfortable working with electrical or mechanical components. When calling, have the full model number, the error code displayed, and a brief description of any sounds or symptoms you noticed before the fault appeared — this helps the technician prepare the correct parts and tools. ## Frequently Asked Questions Q: Is E08 a safety hazard? A leaking element (current to ground) is a safety hazard. Always test for earth leakage before use. Q: Can descaling prevent E08? Yes — heavy limescale insulates the element, causing overheating and failure. Run a descale cycle monthly in hard water areas. Q: Does E08 affect cold wash programmes? Cold wash programmes (20 °C) do not use the heater, so E08 will not appear during a cold wash. ### Is it safe to keep using my Hoover with error E08? If error E08 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E08 on a Hoover ? Repair costs for error E08 on the Hoover washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Hoover-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E08 mean on a Hoover washer? Error code E08 on Hoover washer models indicates Heating element fault — element burned out. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Hoover with error E08? If error E08 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E08 on a Hoover ? Repair costs for error E08 on the Hoover washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Hoover-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E08 mean on a Hoover washer? Error code E08 on Hoover washer models indicates Heating element fault — element burned out. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.