Skip to content
Appliance Error Codes

Error Code E08 on Hoover HT3W7220LFHK Refrigerator | Causes & Fix

Error E08 on Hoover : Ice maker fault — ice production stopped. Follow the troubleshooting steps below to diagnose and fix this refrigerator issue. ## What Error Code E08 Means on a Hoover HT3W7220LFHK E08 on the Hoover HT3W7220LFHK fridge-freezer indicates a fault with the ice maker. The ice maker cycle involves filling a mould, freezing the water, then harvesting the ice by briefly heating the mould and rotating the ejection arm. E08 is raised when the control board detects the ice maker motor has not completed a harvest cycle within the expected time. When E08 appears, the Hoover refrigerator pauses normal operation to protect internal components from potential damage. Not every E08 fault requires a professional engineer — many are resolved through careful inspection and routine maintenance. Work through each diagnostic step below in sequence, starting with the simplest check, to identify the root cause efficiently before considering part replacement or arranging a service call. ## Symptoms - E08 on display

  • No ice cubes being produced
  • Ice maker arm stuck or jammed ## Common Causes - Ice maker fault — ice production stopped ## Tools You May Need - Phillips screwdriver
  • warm water ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Check ice maker arm — if in the UP position, ice maker is off. Lower arm to ON position. | Arm position confirmed — continue to step 2 if the issue persists. | | 2 | Check water supply to fridge is connected and pressure is adequate. | Water supply confirmed — continue to step 3 if the issue persists. | | 3 | Remove ice bin and inspect for jammed ice clumps blocking the ejector arm. | Blockage cleared — continue to step 4 if the issue persists. | | 4 | Pour warm (not hot) water over the ice mould to clear any ice binding the ejector. | Mould cleared — continue to step 5 if the issue persists. | | 5 | If E08 persists, unplug and test ice maker motor winding: typically 10–50 Ω. Replace motor if OL. | Motor tested — if the fault remains, contact a qualified technician. | ## Safety Precautions Unplug before accessing the ice maker motor. Ice ejector blades are sharp — use gloves when clearing jammed ice. ## Estimated Repair Time and Difficulty Most refrigerator error code E08 faults can be assessed and addressed in 30–90 minutes using the steps above. The diagnostic process requires only basic tools: a multimeter and standard screwdrivers cover the majority of checks described here. If a replacement part is required, allow 1–5 working days for delivery. A trained technician with access to the correct diagnostic equipment will typically resolve this type of fault within a single service visit. ## When to Call a Technician Contact a Hoover authorised service technician if: the fault persists after following all the steps above; if PCB-level or refrigerant-circuit work is required; or if you are not comfortable working with electrical or mechanical components. When calling, have the full model number, the error code displayed, and a brief description of any sounds or symptoms you noticed before the fault appeared — this helps the technician prepare the correct parts and tools. ## Frequently Asked Questions Q: Should I turn off the ice maker if I go on holiday? Yes — lift the arm to the OFF position or disable the ice maker in the settings menu if available. Q: How long does the first ice production take after installation? Allow 24 hours for the fridge to reach operating temperature and 24 more hours for the first batch of ice. Q: Can hard water affect the ice maker? Yes — limescale can block the water inlet valve screen and the ice mould fill tube. Use a water filter if available. ### Is it safe to keep using my Hoover with error E08? If error E08 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the refrigerator with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E08 on a Hoover ? Repair costs for error E08 on the Hoover refrigerator depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Hoover-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E08 mean on a Hoover refrigerator? Error code E08 on Hoover refrigerator models indicates Ice maker fault — ice production stopped. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Hoover with error E08? If error E08 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the refrigerator with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E08 on a Hoover ? Repair costs for error E08 on the Hoover refrigerator depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Hoover-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E08 mean on a Hoover refrigerator? Error code E08 on Hoover refrigerator models indicates Ice maker fault — ice production stopped. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.