Skip to content
Appliance Error Codes

Error Code E2 on Hitachi NP-TZ200 Dishwasher | Causes & Fix

Error E2 on Hitachi : Drain fault — machine unable to drain water within the expected time. Follow the troubleshooting steps below to diagnose and fix this dishwasher issue. ## What Error Code E2 Means on a Hitachi NP-TZ200 Dishwasher The E2 error code on the Hitachi NP-TZ200 dishwasher indicates a machine unable to drain water within the expected time. Hitachi NP-series dishwashers continuously monitor water levels, temperatures, motor currents, and sensor feedback throughout each programme. When a reading is outside the accepted threshold or a component fails to respond within the timeout, the dishwasher stops and displays the fault code on the control panel. ## Symptoms - E2 at end of wash or rinse phase

  • standing water in tub after programme end
  • pump noise but water level unchanged
  • E2 immediately at drain phase start ## Common Causes - drain pump motor winding open (OL)
  • pump impeller blocked by debris
  • drain hose kinked or missing high-loop
  • pump filter heavily blocked with food particles ## Tools You May Need - multimeter
  • Phillips screwdriver
  • flat-head screwdriver
  • towel and shallow tray (for sump access) ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Remove the lower tray and locate the pump filter at the bottom of the tub | Check complete | | 2 | Check the drain hose at the rear of the dishwasher for kinks | Check complete | | 3 | Unplug the dishwasher | Check complete | | 4 | Check the drain pump impeller by reaching into the filter housing with a finger — spin the impeller to confirm free rotation | Check complete | | 5 | Reinstall filter, restore power, and run a Drain programme to confirm E2 is resolved | Check complete | ## Safety Precautions Always disconnect the dishwasher from mains power before removing any panels or accessing the sump. Close the water supply valve before disconnecting any water-side components. Allow hot water and steam inside the tub to cool before reaching into the sump area. Do not run the dishwasher without the pump filter in place — an unfiltered sump can damage the circulation pump impeller. ## When to Call a Technician Call a qualified appliance technician if: - the main control PCB requires replacement
  • the circulation pump requires replacement (involves sump removal)
  • the heating element or thermal cutout requires access beyond the filter bay
  • the error persists after all accessible components have been inspected and cleaned ## Preventing Future Faults - clean the pump filter after every 4–6 wash cycles
  • run a dishwasher cleaner or citric acid cycle monthly in hard water areas
  • confirm the salt reservoir is filled in hard water regions
  • leave the door ajar after cycles to air-dry the tub interior
  • load dishes so spray arms can rotate freely ## Frequently Asked Questions ### Is it safe to keep using my Hitachi with error E2? If error E2 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E2 on a Hitachi ? Repair costs for error E2 on the Hitachi dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Hitachi-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E2 mean on a Hitachi dishwasher? Error code E2 on Hitachi dishwasher models indicates Drain fault — machine unable to drain water within the expected time. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Hitachi with error E2? If error E2 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E2 on a Hitachi ? Repair costs for error E2 on the Hitachi dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Hitachi-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E2 mean on a Hitachi dishwasher? Error code E2 on Hitachi dishwasher models indicates Drain fault — machine unable to drain water within the expected time. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.