Skip to content
Appliance Error Codes

Error Code F10 on Hisense HUI66360XCUS Dishwasher | Causes & Fix

Error F10 on Hisense : Flood detection — water found in base pan — AquaStop or overflow protection acti. Follow the troubleshooting steps below to diagnose and fix this dishwasher issue. ## What Error Code F10 Means on a Hisense HUI66360XCUS Dishwasher The F10 error code on the Hisense HUI66360XCUS dishwasher indicates a water found in base pan. The control board monitors water level, temperature, drainage, and flood-protection sensors throughout the cycle. When a reading falls outside the expected window or a component fails to respond, the board halts the programme and displays the fault code. ## Symptoms - F10 on display with no cycle running

  • machine door will not unlock after cycle
  • puddle visible under the dishwasher
  • hissing sound from base of machine ## Common Causes - worn or torn door gasket allowing wash water to drip into base tray
  • cracked tub or sump allowing water to seep into base
  • loose inlet or drain hose connection dripping inside cabinet
  • base tray float switch stuck in triggered position after prior leak ## Tools You May Need - multimeter
  • Phillips screwdriver
  • flat-head screwdriver
  • torch (flashlight)
  • towel and shallow tray ## Step-by-Step Repair Guide | Step | Action | Result | |------|--------|--------| | 1 | Switch off the dishwasher and turn off the water supply valve under the sink | Check complete | | 2 | Carefully tilt the machine forward 45° to drain any standing water from the base drip tray into a towel or shallow tray on the floor | Check complete | | 3 | Inspect the door gasket around the entire perimeter for tears, gaps, or displaced sections | Check complete | | 4 | Check the inlet hose and drain hose connections for drips | Check complete | | 5 | Once the base tray is completely dry, restore power and run a short rinse cycle to confirm F10 does not recur | Check complete | ## Safety Precautions Always disconnect the appliance from mains power before opening any panels or accessing internal components. Allow the unit to cool completely before handling any element, compressor, or heat-producing part. Work in a dry area and keep a towel on the floor when dealing with water-connected appliances. Do not bypass safety interlocks, and ensure the power cord is fully unplugged — not just switched off at the control panel — before measuring component resistance. ## When to Call a Technician Call a qualified appliance technician if: - the base tray shows signs of tub cracking or sealed system damage
  • the main control board requires replacement
  • the error persists after all accessible components have been replaced
  • water damage to kitchen flooring or cabinetry requires professional assessment ## Preventing Future Faults - clean the filter assembly monthly (or more frequently with heavily soiled loads)
  • use the correct amount of HE dishwasher detergent
  • run a maintenance descaling cycle every 3–6 months in hard-water areas
  • inspect the door gasket annually and replace if worn or cracked
  • ensure adequate water pressure — minimum 0.5 bar (7 psi) at the supply valve ## Frequently Asked Questions ### Is it safe to keep using my Hisense with error F10? If error F10 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error F10 on a Hisense ? Repair costs for error F10 on the Hisense dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Hisense-authorized service provider for an accurate estimate based on your specific situation. ### What does error code F10 mean on a Hisense dishwasher? Error code F10 on Hisense dishwasher models indicates Flood detection — water found in base pan — AquaStop or overflow protection activated. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Hisense with error F10? If error F10 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error F10 on a Hisense ? Repair costs for error F10 on the Hisense dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Hisense-authorized service provider for an accurate estimate based on your specific situation. ### What does error code F10 mean on a Hisense dishwasher? Error code F10 on Hisense dishwasher models indicates Flood detection — water found in base pan — AquaStop or overflow protection activated. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.