GE GFW650SSNWW Error Code E67

1. Home ›
2. GE ›
3. Washer ›
4. GFW650SSNWW ›
5. E67

• Source: Official GE service manual
• Reviewed by: Geo Technical Editorial
• Published: March 1, 2026
• Updated: March 15, 2026
• DIY scope: Basic user checks are possible.

Error E67 on GE : Heating element failure or hot/cold supply hoses reversed — wash cycle water tem. Follow the troubleshooting steps below to diagnose and fix this washer issue. ## What Error Code E67 Means on a GE GFW650SSNWW Heating element failure or hot/cold supply hoses reversed — wash cycle water temperature cannot be achieved ## What This Error Means Error code E67 on your GE UltraFresh washer indicates a problem with the wash water heating system. GE UltraFresh front-load washers have a built-in water heater that boosts cold supply water to the temperature required for hot wash cycles, sanitize cycles, and allergen removal cycles. E67 appears in two scenarios: 1. Hot-Cold Reversed (HC code): The hot and cold supply hoses are connected to the wrong inlet ports on the back of the washer. The control board detects this because the initial fill temperature is opposite to what is expected. Fix: swap the two supply hose connections. 2. Heater Element Failure: The internal heating element has burned out (open circuit). The element resistance should be approximately 15 ohms. An open circuit (OL) reading confirms the element has failed. E67 blocks all cycles that require temperature control. Cold water cycles may still operate. ## Quick Diagnostic Summary | Detail | Value | |--------|-------| | Error Code | E67 | | Severity | High | | Appliance | GE GFW650SSNWW GE UltraFresh Washer | | User-Fixable | Yes | | Applicable Models | GFW850SPNRS, GFW650SSNWW, GTW840CPNDG | ## Step-by-Step Troubleshooting | Step | Action | What To Do | Expected Result | |------|--------|------------|-----------------| | 1 | Check if hot and cold supply hoses are reversed | Locate the hot (H) and cold (C) labeled ports on the back of the washer. Verify the hose from your home’s hot water shutoff valve (marked H) is connected to the H port on the washer, and the cold water hose is connected to the C port. Labels may be embossed on the washer body near each port. | Hot supply hose is connected to the H port and cold supply hose is connected to the C port. Hoses are not swapped. | | 2 | Reset the washer after correcting hose connections | If you found and corrected reversed hoses, unplug the washer for 30 seconds then restore power. Run a normal test cycle. E67 or HC should clear once the hose connections are correct. | After correcting hoses and resetting, E67/HC does not appear during a test cycle. Washer operates normally. | | 3 | Test the internal heating element resistance | Unplug the washer. Access the heater element at the bottom-front of the outer tub (behind the lower front panel). Disconnect the heater wiring terminals. Set a multimeter to resistance mode. Test across the two heater terminals — expect approximately 15 ohms. An OL reading confirms the element is burned out. | Heater element reads approximately 15 ohms (normal). OL confirms a burned-out element requiring replacement. | | 4 | Check heater wiring and thermal fuse | With the heater disconnected, inspect the two heater wires for damage. Also locate the thermal fuse (a safety cutout on the heater circuit, typically a small cylindrical component in series with the heater wiring) — test for continuity. An open thermal fuse blocks power to the heater and shows OL. | Heater wires are intact with no damage. Thermal fuse shows continuity (not open). An open thermal fuse requires replacement. | | 5 | Replace heating element (or thermal fuse as applicable) | Order the replacement heater element or thermal fuse for your GE model. With power disconnected, remove the old element (typically 2 retaining bolts), disconnect the wiring, and install the new element with a fresh gasket seal. Reconnect wiring, reassemble, restore power, and run a sanitize cycle to test. | New heater element installed. Sanitize cycle completes, heating water to the required temperature. E67 does not return. | ## Frequently Asked Questions ### What does HC mean on a GE washer? HC stands for Hot-Cold Reversed. It appears when the control board detects that the hot and cold supply hoses are connected to the wrong ports on the back of the washer. The fix is simple: swap the two supply hose connections (turn off the water supply valves first). HC is an installation error, not a component failure. ### Can I wash laundry while E67 is active? On cycles that do not require heated water (cold wash only), some GE washers will continue to function with E67 active. However, any cycle requiring hot water, a sanitize cycle, or an allergen cycle will be blocked. Repair the heater element before relying on temperature-dependent cycles. ### What is the GE washer heater element resistance? The internal water heater element in GE UltraFresh front-load washers measures approximately 15 ohms at room temperature. This is the resistance of the nichrome heating wire inside the element. An open circuit (OL) reading means the wire has burned through and the element must be replaced. A reading near zero indicates a short circuit, which also requires replacement. ### How do I know if the thermal fuse on my GE washer has blown? The thermal fuse is a safety cutout that permanently opens if the heater circuit reaches an unsafe temperature (due to a failed thermostat or restricted water flow). Test it with a multimeter in continuity mode — a healthy fuse shows continuity, a blown fuse shows OL. Once blown, the thermal fuse cannot be reset and must be replaced. Always investigate why the fuse blew (usually a failed thermostat or pump problem) before replacing just the fuse. --- Last Updated: March 2026 · GE GE UltraFresh Washer · Error Code E67 ### Is it safe to keep using my GE with error E67? If error E67 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E67 on a GE ? Repair costs for error E67 on the GE washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a GE-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E67 mean on a GE washer? Error code E67 on GE washer models indicates Heating element failure or hot/cold supply hoses reversed — wash cycle water temperature cannot be a. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my GE with error E67? If error E67 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E67 on a GE ? Repair costs for error E67 on the GE washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a GE-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E67 mean on a GE washer? Error code E67 on GE washer models indicates Heating element failure or hot/cold supply hoses reversed — wash cycle water temperature cannot be a. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.