Skip to content
Appliance Error Codes

GE GFW650SSNWW Error Code E22

Error E22 on GE : Fill timeout — the washer did not reach the required water level within the allo. Follow the troubleshooting steps below to diagnose and fix this washer issue. ## What Error Code E22 Means on a GE GFW650SSNWW Fill timeout — the washer did not reach the required water level within the allowed fill time ## What This Error Means Error code E22 on your GE washer indicates the machine failed to fill with water to the required level within the allowed fill time. The control board monitors the water level sensor; if the sensor does not reach the target level within approximately 8-10 minutes of the fill valve opening, E22 is triggered. Common causes include: water supply valves not fully open, inlet screen filters clogged with mineral deposits or debris, a faulty water inlet valve (one solenoid coil failed), low house water pressure below the minimum 20 psi, or a kinked water supply hose. The water inlet valve solenoid coil resistance for GE washers should measure approximately 200–500 ohms. An OL reading indicates a failed solenoid that will prevent water from entering the tub regardless of supply pressure. ## Quick Diagnostic Summary | Detail | Value | |--------|-------| | Error Code | E22 | | Severity | Medium | | Appliance | GE GFW650SSNWW GE UltraFresh Washer | | User-Fixable | Yes | | Applicable Models | GFW850SPNRS, GFW650SSNWW, GTW840CPNDG | ## Step-by-Step Troubleshooting | Step | Action | What To Do | Expected Result | |------|--------|------------|-----------------| | 1 | Verify water supply valves are fully open | Locate the hot and cold water supply valves behind the washer. Turn both valves counterclockwise until fully open (stops). A partially closed valve restricts water flow and extends fill time, triggering E22. Also confirm no one has closed a valve for maintenance and left it partially closed. | Both hot and cold supply valves are fully open. Water flows freely when a supply hose is briefly disconnected into a bucket. | | 2 | Clean inlet hose screen filters | Turn off both water supply valves. Disconnect the hot and cold supply hoses from the back of the washer. Inside each water connection port on the washer, there is a small mesh screen filter. Remove the screens with needle-nose pliers and rinse under running water to clear mineral deposits. Reinstall screens and reconnect hoses. | Inlet screen filters are clean and free of mineral deposits. Hoses are reconnected and hand-tightened. | | 3 | Test water inlet valve solenoid resistance | Unplug the washer. Pull it away from the wall and access the water inlet valve (at the rear where the supply hoses connect). Disconnect the electrical connector(s) to the valve solenoids. Test each solenoid coil with a multimeter in resistance mode. GE inlet valve solenoids should read approximately 200–500 ohms. | Each solenoid coil reads 200–500 ohms. An OL reading confirms the solenoid has failed and the valve must be replaced. | | 4 | Check house water pressure | GE washers require minimum 20 psi water pressure. To test, disconnect a supply hose and hold it in a bucket — open the valve and measure flow volume over 10 seconds. Adequate pressure at 20+ psi fills approximately 400 mL (13.5 oz) in 10 seconds. Low pressure requires a plumber’s evaluation. | Water flow rate from the supply hose confirms pressure is above 20 psi minimum requirement. | | 5 | Replace water inlet valve if solenoid tests failed | Order the replacement water inlet valve for your specific GE model. Disconnect power and water supply. Disconnect the supply hoses and solenoid wiring harness. Remove the mounting screws and swap in the new valve. Reconnect all connections, restore power and water supply, and run a test cycle. | New inlet valve installed. Washer fills to the correct level within the normal fill time. E22 does not return. | ## Frequently Asked Questions ### Can cold weather cause E22? Yes. In very cold climates, water supply lines that run through unheated spaces (garages, crawl spaces) can partially freeze, reducing or stopping water flow. If E22 appears only in cold weather, check the supply lines for freezing and consider insulating them or rerouting through heated spaces. ### E22 only appears on hot water cycles — why? If E22 appears only during cycles that require hot water, the hot water solenoid in the inlet valve has likely failed. On GE washers with a dual-solenoid inlet valve, one solenoid controls hot water and one controls cold. Test each solenoid independently — the hot solenoid reading OL confirms it needs replacement. ### What water pressure do GE washers need? GE UltraFresh and standard GE washers require a minimum of 20 psi and a maximum of 120 psi. Below 20 psi, the fill valve cannot open properly and the fill cycle times out. The typical household pressure of 40-80 psi is ideal. If you have very high pressure (over 100 psi), a pressure-reducing valve on the supply line is recommended. ### Can a clogged SmartDispense drawer cause E22? On GE UltraFresh models with SmartDispense, the detergent and softener dispenser uses water flow from the inlet valve to dispense into the drum. A blocked dispenser housing can cause the fill valve to open but water not reach the drum properly. Clean the SmartDispense drawer and housing monthly to prevent this. --- Last Updated: March 2026 · GE GE UltraFresh Washer · Error Code E22 ### Is it safe to keep using my GE with error E22? If error E22 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E22 on a GE ? Repair costs for error E22 on the GE washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a GE-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E22 mean on a GE washer? Error code E22 on GE washer models indicates Fill timeout — the washer did not reach the required water level within the allowed fill time. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my GE with error E22? If error E22 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the washer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E22 on a GE ? Repair costs for error E22 on the GE washer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a GE-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E22 mean on a GE washer? Error code E22 on GE washer models indicates Fill timeout — the washer did not reach the required water level within the allowed fill time. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.