GE PDT715SYNFS Error Code PF

1. Home ›
2. GE ›
3. Dishwasher ›
4. PDT715SYNFS ›
5. PF

• Source: Official GE service manual
• Reviewed by: Geo Technical Editorial
• Published: March 1, 2026
• Updated: March 15, 2026
• DIY scope: Basic user checks are possible.

Error PF on GE : Power failure — dishwasher experienced a power interruption during a cycle. Follow the troubleshooting steps below to diagnose and fix this dishwasher issue. ## What Error Code PF Means on a GE PDT715SYNFS Power failure — dishwasher experienced a power interruption during a cycle ## What This Error Means Error code PF on your GE dishwasher is an informational alert indicating the appliance experienced a power interruption during an active wash cycle. This occurs during power outages, tripped circuit breakers, or accidental unplugging while a cycle was running. PF is not a component fault — it simply means power was lost and the cycle was interrupted. GE dishwashers cannot resume an interrupted cycle from where it stopped; you must select a new cycle and start fresh. If PF appears repeatedly without any known power event (no outage, no visible tripped breaker), it can indicate a failing circuit breaker with intermittent contact, a loose connection at the dishwasher junction box or outlet, or occasionally a failing dishwasher control board power supply circuit. ## Quick Diagnostic Summary | Detail | Value | |--------|-------| | Error Code | PF | | Severity | Low | | Appliance | GE PDT715SYNFS GE Profile Dishwasher | | User-Fixable | Yes | | Applicable Models | GDT665SGNBB, GDT695SSJSS, PDT715SYNFS | ## Step-by-Step Troubleshooting | Step | Action | What To Do | Expected Result | |------|--------|------------|-----------------| | 1 | Select a new cycle and restart | Press the Cancel/Reset button to clear PF. Select your desired wash cycle using the cycle selector button, then press Start. The dishwasher will run a fresh, complete cycle from the beginning. | PF clears. New cycle selected and started. Dishwasher runs a complete cycle without interruption. | | 2 | Check the circuit breaker | Go to the home’s electrical service panel and verify the dishwasher circuit breaker is fully in the ON position. A half-tripped breaker (in the middle position) may still provide power intermittently while appearing to be on. Reset by pushing to OFF then firmly to ON. | Circuit breaker is confirmed fully ON. No repeated tripping observed. | | 3 | Verify the dishwasher outlet or junction box connection | If the dishwasher is plugged into an outlet under the sink, confirm the power cord is fully inserted. If direct-wired, turn off the circuit breaker and inspect the junction box connections — ensure all wire nuts are tight and no wires are loose. | Power connection is secure. All wiring connections in junction box are tight. | | 4 | Monitor for recurring PF | Run 3-4 complete dishwasher cycles and observe whether PF returns without any known power event. If PF appears during a cycle without a house-wide power loss, there may be an intermittent issue with the circuit breaker or power supply wiring. | PF does not return during 3-4 consecutive test cycles. Power supply is stable. | | 5 | Install a surge protector if PF was power-event related | If PF appeared during a storm or utility switching, install a dishwasher-rated surge protector on the outlet or contact an electrician about whole-home surge protection. Voltage spikes can damage the dishwasher control board over multiple events. | Surge protector installed. Dishwasher protected from future voltage spikes. | ## Frequently Asked Questions ### Will PF cause any damage to the dishwasher? PF itself is not damaging — it is a notification that a cycle was interrupted. In rare cases, a power surge (high-voltage spike) that accompanies a power event can damage the control board. If the dishwasher behaves erratically after a PF event (unusual cycle behavior, buttons not responding), a power surge may have affected the control board. ### Can I resume a GE dishwasher cycle after PF? GE dishwashers do not support mid-cycle resume. After PF, you must select a new cycle and start from the beginning. If the dishes were partially washed during the interrupted cycle, running a full Normal Wash will complete the cleaning. ### How do I know if a power surge caused PF on my GE dishwasher? If PF appeared during or immediately after a storm, lightning event, or when other appliances on the same circuit showed signs of disruption, a power surge is the likely cause. Inspect the control board (behind the door panel) for any visible discoloration or burned components as confirmation of surge damage. ### PF keeps appearing daily but there are no outages — what is wrong? Daily recurring PF without a known power event suggests an intermittent power supply problem. Common causes: a failing circuit breaker with a loose contact that occasionally disconnects; a loose wire connection at the dishwasher junction box; or a failing control board power supply section. Have an electrician test the circuit breaker and wiring under load before replacing the control board. --- Last Updated: March 2026 · GE GE Profile Dishwasher · Error Code PF ### Is it safe to keep using my GE with error PF? If error PF does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error PF on a GE ? Repair costs for error PF on the GE dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a GE-authorized service provider for an accurate estimate based on your specific situation. ### What does error code PF mean on a GE dishwasher? Error code PF on GE dishwasher models indicates Power failure — dishwasher experienced a power interruption during a cycle. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my GE with error PF? If error PF does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dishwasher with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error PF on a GE ? Repair costs for error PF on the GE dishwasher depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a GE-authorized service provider for an accurate estimate based on your specific situation. ### What does error code PF mean on a GE dishwasher? Error code PF on GE dishwasher models indicates Power failure — dishwasher experienced a power interruption during a cycle. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.