Skip to content
Appliance Error Codes

Error Code E10 on Electrolux EFDE317TIW Dryer | Causes & Fix

Error E10 on Electrolux : Inlet air thermistor fault — temperature sensor reading out of range. Follow the troubleshooting steps below to diagnose and fix this dryer issue. ## What Error Code E10 Means on an Electrolux EFDE317TIW Dryer The E10 error code on an Electrolux dryer indicates that the inlet air thermistor (the temperature sensor measuring incoming air before the heater) has returned a reading outside the valid operating range. The control board monitors this sensor to regulate drying temperatures and protect against overheating. ## Symptoms - E10 on the display at start or during a drying cycle

  • dryer runs but produces no heat
  • dryer runs extremely hot and stops early
  • cycle time unexpectedly short or long ## Common Causes - faulty inlet NTC thermistor (normal resistance at 70°F/21°C: approximately 50,000 Ω; out-of-range below ~5,000 Ω or above ~200,000 Ω)
  • loose or corroded thermistor wiring connector
  • thermistor mounted incorrectly or fallen out of its bracket
  • control board unable to read thermistor signal ## Tools You May Need - multimeter
  • Phillips screwdriver
  • flat-head screwdriver ## Step-by-Step Repair Guide | Step | Action | Expected Result | |------|--------|-----------------| | 1 | Unplug the dryer from the power outlet. Allow 5 minutes for residual heat to dissipate before opening the cabinet. | Machine is de-energized and cool enough to handle safely. | | 2 | Remove the rear access panel (typically 4–6 screws). Locate the inlet NTC thermistor — it is usually mounted in the air duct near the heater inlet, identifiable by two thin wires. | Thermistor is accessible for testing. | | 3 | Disconnect the thermistor’s wiring connector. Set your multimeter to resistance (Ω) and measure across the two thermistor terminals at room temperature (approximately 21°C/70°F). Normal reading is approximately 50,000 Ω. Replace if outside 5,000–200,000 Ω. | Thermistor electrical condition is confirmed. | | 4 | Check the wiring harness from the thermistor to the control board for damaged insulation, bent connector pins, or loose connections. Repair or replace damaged wiring. | Wiring path is confirmed intact. | | 5 | If the thermistor and wiring test correctly and E10 persists, the control board input circuit may be faulty. Have the board inspected or replaced by a qualified technician. | Root cause is identified. | ## Frequently Asked Questions What is the resistance of the Electrolux dryer inlet thermistor? At room temperature (approximately 21°C/70°F) the inlet NTC thermistor should read approximately 50,000 Ω. Resistance decreases as temperature rises — this is normal NTC behavior. Can I test the thermistor while the dryer is hot? You can test it hot, but the resistance will be much lower — possibly 1,000–3,000 Ω at typical drying temperatures. Always compare to the specified room-temperature value for diagnostic purposes. Will E10 prevent the dryer from running? Yes. When E10 is active, the dryer will stop or refuse to start a heat cycle as a safety measure to prevent uncontrolled temperatures. Is E10 the same as E60 on a washer? They are related in concept (both are thermistor/heating faults) but E10 on the dryer specifically refers to the inlet air temperature sensor. E60 on the washer refers to the water heating system. --- Always unplug the appliance before performing any repair. If you are unsure, contact a certified Electrolux service technician or call Electrolux support at 1-877-435-3287. ### Is it safe to keep using my Electrolux with error E10? If error E10 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dryer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E10 on a Electrolux ? Repair costs for error E10 on the Electrolux dryer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Electrolux-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E10 mean on a Electrolux dryer? Error code E10 on Electrolux dryer models indicates Inlet air thermistor fault — temperature sensor reading out of range. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue. ### Is it safe to keep using my Electrolux with error E10? If error E10 does not indicate an immediate safety hazard such as a gas leak, electrical short, or water flooding, you can continue limited use while monitoring the appliance. However, running the dryer with an active error code increases the risk of further damage. Address the underlying issue as soon as possible. For high-severity errors, disconnect the appliance and contact a qualified technician. ### How much does it cost to fix error E10 on a Electrolux ? Repair costs for error E10 on the Electrolux dryer depend on the root cause. DIY fixes such as cleaning filters, resetting the unit, or reconnecting loose wires cost nothing beyond basic tools. If a component replacement is needed, parts and labor from a certified technician are the main expenses. Contact a Electrolux-authorized service provider for an accurate estimate based on your specific situation. ### What does error code E10 mean on a Electrolux dryer? Error code E10 on Electrolux dryer models indicates Inlet air thermistor fault — temperature sensor reading out of range. This error is detected by the appliance’s internal diagnostic system and displayed to alert the user that attention is needed. Refer to the troubleshooting steps above for guidance on resolving this issue.